Mitsubishi Keyless Entry Remote Fob Programming Instructions
Keyless Entry Remote Fob Programming Instructions Available for the following Mitsubishi models.
Click below to select your model.
| Model | Year | |
|---|---|---|
| Mitsubishi Diamante | 2000 | Programming Instructions |
| Mitsubishi Diamante | 2001 | Programming Instructions |
| Mitsubishi Diamante | 2002 | Programming Instructions |
| Mitsubishi Diamante | 2003 | Programming Instructions |
| Mitsubishi Diamante | 2004 | Programming Instructions |
2000 Mitsubishi Diamante Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Mitsubishi Diamante Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Mitsubishi Diamante Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Mitsubishi Diamante Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2003 Mitsubishi Diamante Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Mitsubishi Diamante Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2004 Mitsubishi Diamante Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Mitsubishi Diamante Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
| Model | Year | |
|---|---|---|
| Mitsubishi Eclipse | 2000 | Programming Instructions |
| Mitsubishi Eclipse | 2001 | Programming Instructions |
| Mitsubishi Eclipse | 2002 | Programming Instructions |
| Mitsubishi Eclipse | 2003 | Programming Instructions |
| Mitsubishi Eclipse | 2004 | Programming Instructions |
| Mitsubishi Eclipse | 2005 | Programming Instructions |
| Mitsubishi Eclipse | 2006 | Programming Instructions |
| Mitsubishi Eclipse | 2007 | Programming Instructions |
| Mitsubishi Eclipse | 2008 | Programming Instructions |
| Mitsubishi Eclipse | 2009 | Programming Instructions |
| Mitsubishi Eclipse | 2010 | Programming Instructions |
| Mitsubishi Eclipse | 2011 | Programming Instructions |
| Mitsubishi Eclipse | 2012 | Programming Instructions |
2000 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Mitsubishi Eclipse Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2003 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Mitsubishi Eclipse Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2004 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Mitsubishi Eclipse Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2005 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Mitsubishi Eclipse Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2006 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Mitsubishi Eclipse Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2007 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Mitsubishi Eclipse Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2008 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Mitsubishi Eclipse Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Mitsubishi Endeavor | 2004 | Programming Instructions |
| Mitsubishi Endeavor | 2005 | Programming Instructions |
| Mitsubishi Endeavor | 2006 | Programming Instructions |
| Mitsubishi Endeavor | 2007 | Programming Instructions |
| Mitsubishi Endeavor | 2008 | Programming Instructions |
| Mitsubishi Endeavor | 2010 | Programming Instructions |
2004 Mitsubishi Endeavor Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Mitsubishi Endeavor Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2005 Mitsubishi Endeavor Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Mitsubishi Endeavor Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2006 Mitsubishi Endeavor Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Mitsubishi Endeavor Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2007 Mitsubishi Endeavor Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Mitsubishi Endeavor Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2008 Mitsubishi Endeavor Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Mitsubishi Endeavor Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2010 Mitsubishi Endeavor Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Mitsubishi Galant | 2000 | Programming Instructions |
| Mitsubishi Galant | 2001 | Programming Instructions |
| Mitsubishi Galant | 2002 | Programming Instructions |
| Mitsubishi Galant | 2003 | Programming Instructions |
| Mitsubishi Galant | 2004 | Programming Instructions |
| Mitsubishi Galant | 2005 | Programming Instructions |
| Mitsubishi Galant | 2006 | Programming Instructions |
| Mitsubishi Galant | 2007 | Programming Instructions |
| Mitsubishi Galant | 2008 | Programming Instructions |
| Mitsubishi Galant | 2009 | Programming Instructions |
| Mitsubishi Galant | 2010 | Programming Instructions |
| Mitsubishi Galant | 2011 | Programming Instructions |
| Mitsubishi Galant | 2012 | Programming Instructions |
2000 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Mitsubishi Galant Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2003 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Mitsubishi Galant Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2004 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Mitsubishi Galant Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2005 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Mitsubishi Galant Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2006 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Mitsubishi Galant Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2007 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Mitsubishi Galant Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2008 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Mitsubishi Galant Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Mitsubishi i-MiEV | 2012 | Programming Instructions |
2012 Mitsubishi i-MiEV Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Mitsubishi Lancer | 2003 | Programming Instructions |
| Mitsubishi Lancer | 2004 | Programming Instructions |
| Mitsubishi Lancer | 2005 | Programming Instructions |
| Mitsubishi Lancer | 2006 | Programming Instructions |
| Mitsubishi Lancer | 2007 | Programming Instructions |
| Mitsubishi Lancer | 2008 | Programming Instructions |
| Mitsubishi Lancer | 2009 | Programming Instructions |
| Mitsubishi Lancer | 2010 | Programming Instructions |
| Mitsubishi Lancer | 2011 | Programming Instructions |
| Mitsubishi Lancer | 2012 | Programming Instructions |
| Mitsubishi Lancer | 2013 | Programming Instructions |
2003 Mitsubishi Lancer Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Mitsubishi Lancer Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Mitsubishi Lancer Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Mitsubishi Lancer Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Mitsubishi Lancer Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Mitsubishi Lancer Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Mitsubishi Lancer Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Mitsubishi Lancer Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Mitsubishi Lancer Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Mitsubishi Lancer Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2013 Mitsubishi Lancer Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Mitsubishi Montero | 2001 | Programming Instructions |
| Mitsubishi Montero | 2002 | Programming Instructions |
| Mitsubishi Montero | 2003 | Programming Instructions |
| Mitsubishi Montero | 2004 | Programming Instructions |
| Mitsubishi Montero | 2005 | Programming Instructions |
| Mitsubishi Montero | 2006 | Programming Instructions |
2001 Mitsubishi Montero Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Mitsubishi Montero Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Mitsubishi Montero Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2003 Mitsubishi Montero Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Mitsubishi Montero Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2004 Mitsubishi Montero Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Mitsubishi Montero Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2005 Mitsubishi Montero Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Mitsubishi Montero Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2006 Mitsubishi Montero Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Mitsubishi Montero Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
| Model | Year | |
|---|---|---|
| Mitsubishi Montero Sport | 2000 | Programming Instructions |
| Mitsubishi Montero Sport | 2001 | Programming Instructions |
| Mitsubishi Montero Sport | 2002 | Programming Instructions |
| Mitsubishi Montero Sport | 2003 | Programming Instructions |
| Mitsubishi Montero Sport | 2004 | Programming Instructions |
2000 Mitsubishi Montero Sport Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Mitsubishi Montero Sport Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Mitsubishi Montero Sport Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Mitsubishi Montero Sport Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2003 Mitsubishi Montero Sport Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Mitsubishi Montero Sport Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2004 Mitsubishi Montero Sport Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Mitsubishi Montero Sport Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
**2000 and 2001 VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER **
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work.
- Insert an existing first (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) for 5 seconds and back to OFF and remove the key.
- WITHIN SEVEN SECONDS, insert a second working key and turn to ON. The security light will flash twice. Switch ignition back to OFF and Remove key.
- WITHIN SEVEN SECONDS insert the New (unprogrammed) key and turn to ON.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
- Turn ignition to OFF and remote new programmed key. Repeat steps 4 and 5 to program additional keys if any. All new keys must be programmed within 30 seconds of removing second programmed key and security light flashing twice.
- To exit programming mode: leave ignition switched ON for more than 30 seconds.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
| Model | Year | |
|---|---|---|
| Mitsubishi Outlander | 2007 | Programming Instructions |
| Mitsubishi Outlander | 2008 | Programming Instructions |
| Mitsubishi Outlander | 2009 | Programming Instructions |
| Mitsubishi Outlander | 2010 | Programming Instructions |
| Mitsubishi Outlander | 2011 | Programming Instructions |
| Mitsubishi Outlander | 2012 | Programming Instructions |
| Mitsubishi Outlander | 2013 | Programming Instructions |
2007 Mitsubishi Outlander Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Mitsubishi Outlander Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Mitsubishi Outlander Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Mitsubishi Outlander Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Mitsubishi Outlander Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Mitsubishi Outlander Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2013 Mitsubishi Outlander Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Mitsubishi Outlander Sport | 2011 | Programming Instructions |
2011 Outlander Sport Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Mitsubishi Raider | 2006 | Programming Instructions |
| Mitsubishi Raider | 2007 | Programming Instructions |
| Mitsubishi Raider | 2008 | Programming Instructions |
| Mitsubishi Raider | 2009 | Programming Instructions |
2006 Mitsubishi Raider Keyless Entry Remote Fob Programming Instructions
Transponder Vehicles:
Transmitter for the remote key combo is programmed during the Key Programming procedure. Click on the Key Programming for your vehicle to access programming instructions.
NON-Transponder Vehicles:
This programming procedure requires you to already have at least 1 working original remote transmitter. (All buttons must be functional). If you do not have any remote transmitters you must get this new one programmed by a qualified locksmith or dealership.
Obtain all remote transmitters for this vehicle. Any existing keys/remote transmitters not used during programming will become inoperative so make sure to reprogram them during procedure describe below. Sit in vehicle with all doors closed and the driver’s seat-belt on. Make sure no one else is in the vehicle.
- Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
- Using a programmed key/remote transmitter perform the following: Press and hold UNLOCK button.
- After holding the UNLOCK button for a at least 4 seconds, continue holding the UNLOCK button and also press PANIC button within 6 seconds.
- Ensure acoustic signal is emitted indicating programming mode active.
- Within 60 seconds carry out the following procedure for each remaining key/remote transmitter: On the unprogrammed remote, press both the LOCK and UNLOCK button at the same time for 2 seconds then release both buttons.
- Release both buttons.
- Ensure acoustic signal is emitted
- Within 4 seconds press and release the UNLOCK button.
- Ensure acoustic signal is emitted
- Repeat step 3 now for each remaining key/remote transmitters including working remotes.
- Switch ignition to OFF position or wait 60 seconds to exit programming mode.
- Programming is now complete. Test all remotes to ensure proper programming.
Please note: a maximum 6 key remote transmitters can be programmed
Please note: if the vehicle goes into programming mode, but there is no acoustic signal from the new remote, then repeat this procedure again starting from 1st Step.
2006 Mitsubishi Raider Key Programming Instructions
Transponder Vehicles:
You must have two working programmed or original keys to use this procedure.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 seconds you should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming is completed.
- For each additional key you must repeat these steps starting with step number 1.
NON-Transponder Vehicles:
Programming is not required, just get the key blade cut at your local locksmith/dealer and it will start the engine.
2007 Mitsubishi Raider Keyless Entry Remote Fob Programming Instructions
Transponder Vehicles:
Transmitter for the remote key combo is programmed during the Key Programming procedure. Click on the Key Programming for your vehicle to access programming instructions.
NON-Transponder Vehicles:
This programming procedure requires you to already have at least 1 working original remote transmitter. (All buttons must be functional). If you do not have any remote transmitters you must get this new one programmed by a qualified locksmith or dealership.
Obtain all remote transmitters for this vehicle. Any existing keys/remote transmitters not used during programming will become inoperative so make sure to reprogram them during procedure describe below. Sit in vehicle with all doors closed and the driver’s seat-belt on. Make sure no one else is in the vehicle.
- Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
- Using a programmed key/remote transmitter perform the following: Press and hold UNLOCK button.
- After holding the UNLOCK button for a at least 4 seconds, continue holding the UNLOCK button and also press PANIC button within 6 seconds.
- Ensure acoustic signal is emitted indicating programming mode active.
- Within 60 seconds carry out the following procedure for each remaining key/remote transmitter: On the unprogrammed remote, press both the LOCK and UNLOCK button at the same time for 2 seconds then release both buttons.
- Release both buttons.
- Ensure acoustic signal is emitted
- Within 4 seconds press and release the UNLOCK button.
- Ensure acoustic signal is emitted
- Repeat step 3 now for each remaining key/remote transmitters including working remotes.
- Switch ignition to OFF position or wait 60 seconds to exit programming mode.
- Programming is now complete. Test all remotes to ensure proper programming.
Please note: a maximum 6 key remote transmitters can be programmed
Please note: if the vehicle goes into programming mode, but there is no acoustic signal from the new remote, then repeat this procedure again starting from 1st Step.
2007 Mitsubishi Raider Key Programming Instructions
Transponder Vehicles:
You must have two working programmed or original keys to use this procedure.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 seconds you should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming is completed.
- For each additional key you must repeat these steps starting with step number 1.
NON-Transponder Vehicles:
Programming is not required, just get the key blade cut at your local locksmith/dealer and it will start the engine.
2008 Mitsubishi Raider Keyless Entry Remote Fob Programming Instructions
Transponder Vehicles:
Transmitter for the remote key combo is programmed during the Key Programming procedure. Click on the Key Programming for your vehicle to access programming instructions.
NON-Transponder Vehicles:
This programming procedure requires you to already have at least 1 working original remote transmitter. (All buttons must be functional). If you do not have any remote transmitters you must get this new one programmed by a qualified locksmith or dealership.
Obtain all remote transmitters for this vehicle. Any existing keys/remote transmitters not used during programming will become inoperative so make sure to reprogram them during procedure describe below. Sit in vehicle with all doors closed and the driver’s seat-belt on. Make sure no one else is in the vehicle.
- Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
- Using a programmed key/remote transmitter perform the following: Press and hold UNLOCK button.
- After holding the UNLOCK button for a at least 4 seconds, continue holding the UNLOCK button and also press PANIC button within 6 seconds.
- Ensure acoustic signal is emitted indicating programming mode active.
- Within 60 seconds carry out the following procedure for each remaining key/remote transmitter: On the unprogrammed remote, press both the LOCK and UNLOCK button at the same time for 2 seconds then release both buttons.
- Release both buttons.
- Ensure acoustic signal is emitted
- Within 4 seconds press and release the UNLOCK button.
- Ensure acoustic signal is emitted
- Repeat step 3 now for each remaining key/remote transmitters including working remotes.
- Switch ignition to OFF position or wait 60 seconds to exit programming mode.
- Programming is now complete. Test all remotes to ensure proper programming.
Please note: a maximum 6 key remote transmitters can be programmed
Please note: if the vehicle goes into programming mode, but there is no acoustic signal from the new remote, then repeat this procedure again starting from 1st Step.
2008 Mitsubishi Raider Key Programming Instructions
Transponder Vehicles:
You must have two working programmed or original keys to use this procedure.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 seconds you should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming is completed.
- For each additional key you must repeat these steps starting with step number 1.
NON-Transponder Vehicles:
Programming is not required, just get the key blade cut at your local locksmith/dealer and it will start the engine.
2009 Mitsubishi Raider Keyless Entry Remote Fob Programming Instructions
Transponder Vehicles:
Transmitter for the remote key combo is programmed during the Key Programming procedure. Click on the Key Programming for your vehicle to access programming instructions.
NON-Transponder Vehicles:
This programming procedure requires you to already have at least 1 working original remote transmitter. (All buttons must be functional). If you do not have any remote transmitters you must get this new one programmed by a qualified locksmith or dealership.
Obtain all remote transmitters for this vehicle. Any existing keys/remote transmitters not used during programming will become inoperative so make sure to reprogram them during procedure describe below. Sit in vehicle with all doors closed and the driver’s seat-belt on. Make sure no one else is in the vehicle.
- Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
- Using a programmed key/remote transmitter perform the following: Press and hold UNLOCK button.
- After holding the UNLOCK button for a at least 4 seconds, continue holding the UNLOCK button and also press PANIC button within 6 seconds.
- Ensure acoustic signal is emitted indicating programming mode active.
- Within 60 seconds carry out the following procedure for each remaining key/remote transmitter: On the unprogrammed remote, press both the LOCK and UNLOCK button at the same time for 2 seconds then release both buttons.
- Release both buttons.
- Ensure acoustic signal is emitted
- Within 4 seconds press and release the UNLOCK button.
- Ensure acoustic signal is emitted
- Repeat step 3 now for each remaining key/remote transmitters including working remotes.
- Switch ignition to OFF position or wait 60 seconds to exit programming mode.
- Programming is now complete. Test all remotes to ensure proper programming.
Please note: a maximum 6 key remote transmitters can be programmed
Please note: if the vehicle goes into programming mode, but there is no acoustic signal from the new remote, then repeat this procedure again starting from 1st Step.
20099 Mitsubishi Raider Key Programming Instructions
Transponder Vehicles:
You must have two working programmed or original keys to use this procedure.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 seconds you should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming is completed.
- For each additional key you must repeat these steps starting with step number 1.
NON-Transponder Vehicles:
Programming is not required, just get the key blade cut at your local locksmith/dealer and it will start the engine.
