Chevrolet Keyless Entry Remote Fob Programming Instructions Page 2
Keyless Entry Remote Fob Programming Instructions Available for the following Chevrolet models.
Click below to select your model.
Model | Year | |
---|---|---|
Chevrolet Malibu | 2001 | Programming Instructions |
Chevrolet Malibu | 2002 | Programming Instructions |
Chevrolet Malibu | 2003 | Programming Instructions |
Chevrolet Malibu | 2004 | Programming Instructions |
Chevrolet Malibu | 2005 | Programming Instructions |
Chevrolet Malibu | 2006 | Programming Instructions |
Chevrolet Malibu | 2007 | Programming Instructions |
Chevrolet Malibu | 2008 | Programming Instructions |
Chevrolet Malibu | 2009 | Programming Instructions |
Chevrolet Malibu | 2010 | Programming Instructions |
Chevrolet Malibu | 2011 | Programming Instructions |
Chevrolet Malibu | 2012 | Programming Instructions |
Chevrolet Malibu | 2013 | Programming Instructions |
Chevrolet Malibu | 2014 | Programming Instructions |
Chevrolet Malibu | 2015 | Programming Instructions |
Chevrolet Malibu | 2016 | Programming Instructions |
Chevrolet Malibu | 2017 | Programming Instructions |
Chevrolet Malibu | 2018 | Programming Instructions |
Chevrolet Malibu | 2019 | Programming Instructions |
Chevrolet Malibu | 2020 | Programming Instructions |
2001 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2004 Chevrolet Malibu Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Malibu) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2005 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2005 Chevrolet Malibu Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Malibu) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2006 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2006 Chevrolet Malibu Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Malibu) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2007 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2007 Chevrolet Malibu Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Malibu) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2008 Chevrolet Malibu Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Malibu) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2009 Chevrolet Malibu Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Malibu) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2010 Chevrolet Malibu Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Malibu) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2011 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2011 Chevrolet Malibu Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Malibu) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2012 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2012 Chevrolet Malibu Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Malibu) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2013 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2014 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
This procedure requires that a programmed working key is available for the vehicle. This procedure adds keys only. The procedure does not erase previously learned keys. The new key to be programmed needs to be cut prior to performing this programming procedure.
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2015 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
This procedure requires that a programmed working key is available for the vehicle. This procedure adds keys only. The procedure does not erase previously learned keys. The new key to be programmed needs to be cut prior to performing this programming procedure.
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2016 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
This procedure requires that a programmed working key is available for the vehicle. This procedure adds keys only. The procedure does not erase previously learned keys. The new key to be programmed needs to be cut prior to performing this programming procedure.
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2017 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2018 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2019 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2020 Chevrolet Malibu Keyless Entry Remote Fob Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
Model | Year | |
---|---|---|
Chevrolet Malibu Classic | 2005 | Programming Instructions |
2005 Chevrolet Malibu Classic Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed torelease in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock toconfirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
PLEASE NOTE: THESE INSTRUCTIONS WILL NOT WORK IF YOU HAVE ONE OF THE FOLLOWING VEHICLES. If you have oneof these vehicles then you will need to get the remote programmed by a qualified locksmith or dealership.
- 2000 – 2004 Cadillac Seville/Deville
- 2001 – 2006 Chevrolet Astro/Express
- 2001 – 2005 Chevrolet Blazer (SUV – not pickup)
- 2001 – 2004 Chevrolet Corvette
- 2001 – 2005 Chevrolet Monte Carlo
- 2001 – 2004 Chevrolet Malibu
- 2001 – 2004 GMC Jimmy
- 2001 – 2005 GMC Safari
- 2000 – 2005 Pontiac Bonneville
- 2004 Pontiac Grand Prix
2001-2005 Chevrolet Impala, Monte Carlo instructions
- Turn the ignition to ACC or ON and the radio to off. Do not crank the engine.
- Press and hold the DISP button on the radio for at least five seconds until settings is displayed.
- Press the SEEK up or down arrows until FOB PROG appears on the display.
- Press the PREV or NEXT button to enter the submenu. The current selection will have an asterisk next to it. BEGIN willbe displayed.
- Press the DISP button to start programming. When the message PUSH FOB flashes, press and hold the LOCK andUNLOCK buttons on the first transmitter at the same time for 15 seconds. A chime will be heard to verify the transmitter islearned.
- Repeat Step 5 for each additional transmitter up to four remotes total. You do not need to press the DISP button again,just press down the LOCK and UNLOCK buttons on the next transmitter to be learned to a maximum of four transmittersper vehicle.The mode you selected is now set. You can either exit the programming mode by following the instructions later in thissection or program the next feature available on your vehicle.
EXIT (Exit Feature Customization Mode): This feature allows you to exit the vehicle customization programming.
To Exit:
- Scroll until EXIT appears on the display.
- Press the DISP button to exit programming. A chime will he heard to verify the exit.
2005 Chevrolet Malibu Classic Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Chevrolet Monte Carlo | 2001 | Programming Instructions |
Chevrolet Monte Carlo | 2002 | Programming Instructions |
Chevrolet Monte Carlo | 2003 | Programming Instructions |
Chevrolet Monte Carlo | 2004 | Programming Instructions |
Chevrolet Monte Carlo | 2005 | Programming Instructions |
Chevrolet Monte Carlo | 2006 | Programming Instructions |
Chevrolet Monte Carlo | 2007 | Programming Instructions |
2001 Chevrolet Monte Carlo Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Chevrolet Monte Carlo Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Chevrolet Monte Carlo Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Chevrolet Monte Carlo Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Chevrolet Monte Carlo Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Chevrolet Monte Carlo Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2006 Chevrolet Monte Carlo Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2007 Chevrolet Monte Carlo Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2007 Chevrolet Monte Carlo Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
Model | Year | |
---|---|---|
Chevrolet S10 | 1999 | Programming Instructions |
Chevrolet S10 | 2000 | Programming Instructions |
Chevrolet S10 | 2001 | Programming Instructions |
Chevrolet S10 | 2002 | Programming Instructions |
Chevrolet S10 | 2003 | Programming Instructions |
Chevrolet S10 | 2004 | Programming Instructions |
1999 Chevrolet S10 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Chevrolet S10 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2000 Chevrolet S10 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Chevrolet S10 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2001 Chevrolet S10 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Chevrolet S10 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2002 Chevrolet S10 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Chevrolet S10 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2003 Chevrolet S10 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Chevrolet S10 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2004 Chevrolet S10 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Chevrolet Silverado | 1999 | Programming Instructions |
Chevrolet Silverado | 2007 | Programming Instructions |
Chevrolet Silverado | 2008 | Programming Instructions |
Chevrolet Silverado | 2009 | Programming Instructions |
Chevrolet Silverado | 2010 | Programming Instructions |
Chevrolet Silverado | 2011 | Programming Instructions |
Chevrolet Silverado | 2012 | Programming Instructions |
Chevrolet Silverado | 2013 | Programming Instructions |
Chevrolet Silverado | 2014 | Programming Instructions |
Chevrolet Silverado | 2015 | Programming Instructions |
Chevrolet Silverado | 2016 | Programming Instructions |
1999 Chevrolet Silverado Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Chevrolet Silverado Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Chevrolet Silverado Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Chevrolet Silverado Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Chevrolet Silverado Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Chevrolet Silverado Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Chevrolet Silverado Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Chevrolet Silverado Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Chevrolet Silverado Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2011 Chevrolet Silverado Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Chevrolet Silverado Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2012 Chevrolet Silverado Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Chevrolet Silverado Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2013 Chevrolet Silverado Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2013 Chevrolet Silverado Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2014 Chevrolet Silverado Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2014 Chevrolet Silverado Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2015 Chevrolet Silverado Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2015 Chevrolet Silverado Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2016 Chevrolet Silverado Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2016 Chevrolet Silverado Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
Model | Year | |
---|---|---|
Chevrolet Silverado 1500 | 1999 | Programming Instructions |
Chevrolet Silverado 1500 | 2000 | Programming Instructions |
Chevrolet Silverado 1500 | 2001 | Programming Instructions |
Chevrolet Silverado 1500 | 2002 | Programming Instructions |
Chevrolet Silverado 1500 | 2003 | Programming Instructions |
Chevrolet Silverado 1500 | 2004 | Programming Instructions |
Chevrolet Silverado 1500 | 2005 | Programming Instructions |
Chevrolet Silverado 1500 | 2006 | Programming Instructions |
Chevrolet Silverado 1500 | 2007 | Programming Instructions |
Chevrolet Silverado 1500 | 2008 | Programming Instructions |
Chevrolet Silverado 1500 | 2009 | Programming Instructions |
Chevrolet Silverado 1500 | 2010 | Programming Instructions |
Chevrolet Silverado 1500 | 2011 | Programming Instructions |
Chevrolet Silverado 1500 | 2012 | Programming Instructions |
Chevrolet Silverado 1500 | 2013 | Programming Instructions |
1999 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
1999 Chevrolet Silverado 1500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2000 Chevrolet Silverado 1500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2001 Chevrolet Silverado 1500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2002 Chevrolet Silverado 1500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2003 Chevrolet Silverado 1500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2004 Chevrolet Silverado 1500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2005 Chevrolet Silverado 1500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2006 Chevrolet Silverado 1500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2007 Chevrolet Silverado 1500 Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2008 Chevrolet Silverado 1500 Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2009 Chevrolet Silverado 1500 Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2010 Chevrolet Silverado 1500 Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2011 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Chevrolet Silverado 1500 Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2012 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Chevrolet Silverado 1500 Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2013 Chevrolet Silverado 1500 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Chevrolet Silverado 1500 HD | 2001 | Programming Instructions |
Chevrolet Silverado 1500 HD | 2002 | Programming Instructions |
Chevrolet Silverado 1500 HD | 2003 | Programming Instructions |
Chevrolet Silverado 1500 HD | 2004 | Programming Instructions |
Chevrolet Silverado 1500 HD | 2005 | Programming Instructions |
Chevrolet Silverado 1500 HD | 2006 | Programming Instructions |
Chevrolet Silverado 1500 HD | 2007 | Programming Instructions |
2001 Chevrolet Silverado 1500 HD Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2001 Chevrolet Silverado 1500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Chevrolet Silverado 1500 HD Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2002 Chevrolet Silverado 1500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Chevrolet Silverado 1500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2003 Chevrolet Silverado 1500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Chevrolet Silverado 1500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2004 Chevrolet Silverado 1500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Chevrolet Silverado 1500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2005 Chevrolet Silverado 1500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Chevrolet Silverado 1500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2006 Chevrolet Silverado 1500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Chevrolet Silverado 1500 HD Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2007 Chevrolet Silverado 1500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
Model | Year | |
---|---|---|
Chevrolet Silverado 2500 | 1999 | Programming Instructions |
Chevrolet Silverado 2500 | 2000 | Programming Instructions |
Chevrolet Silverado 2500 | 2001 | Programming Instructions |
Chevrolet Silverado 2500 | 2002 | Programming Instructions |
Chevrolet Silverado 2500 | 2003 | Programming Instructions |
Chevrolet Silverado 2500 | 2004 | Programming Instructions |
Chevrolet Silverado 2500 | 2005 | Programming Instructions |
1999 Chevrolet Silverado 2500 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Chevrolet Silverado 2500 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Chevrolet Silverado 2500 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2001 Chevrolet Silverado 2500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Chevrolet Silverado 2500 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2002 Chevrolet Silverado 2500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Chevrolet Silverado 2500 Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2003 Chevrolet Silverado 2500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Chevrolet Silverado 2500 Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2004 Chevrolet Silverado 2500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Chevrolet Silverado 2500 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Chevrolet Silverado 2500 HD | 2001 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2002 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2003 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2004 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2005 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2006 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2007 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2008 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2009 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2010 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2011 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2012 | Programming Instructions |
Chevrolet Silverado 2500 HD | 2013 | Programming Instructions |
2001 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2001 Chevrolet Silverado 2500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2002 Chevrolet Silverado 2500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2003 Chevrolet Silverado 2500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2004 Chevrolet Silverado 2500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2005 Chevrolet Silverado 2500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2006 Chevrolet Silverado 2500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2007 Chevrolet Silverado 2500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2008 Chevrolet Silverado 2500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2009 Chevrolet Silverado 2500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2010 Chevrolet Silverado 2500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2011 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Chevrolet Silverado 2500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2012 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Chevrolet Silverado 2500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2013 Chevrolet Silverado 2500 HD Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Chevrolet Silverado 3500 | 2001 | Programming Instructions |
Chevrolet Silverado 3500 | 2002 | Programming Instructions |
Chevrolet Silverado 3500 | 2003 | Programming Instructions |
Chevrolet Silverado 3500 | 2004 | Programming Instructions |
Chevrolet Silverado 3500 | 2005 | Programming Instructions |
Chevrolet Silverado 3500 | 2006 | Programming Instructions |
Chevrolet Silverado 3500 | 2007 | Programming Instructions |
2001 Chevrolet Silverado 3500 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2001 Chevrolet Silverado 3500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Chevrolet Silverado 3500 Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2002 Chevrolet Silverado 3500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Chevrolet Silverado 3500 Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2003 Chevrolet Silverado 3500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Chevrolet Silverado 3500 Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2004 Chevrolet Silverado 3500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Chevrolet Silverado 3500 Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2005 Chevrolet Silverado 3500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Chevrolet Silverado 3500 Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2006 Chevrolet Silverado 3500 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Chevrolet Silverado 3500 Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2007 Chevrolet Silverado 3500 Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
Model | Year | |
---|---|---|
Chevrolet Silverado 3500 HD | 2001 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2002 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2003 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2004 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2005 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2006 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2007 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2008 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2009 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2010 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2011 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2012 | Programming Instructions |
Chevrolet Silverado 3500 HD | 2013 | Programming Instructions |
2001 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2001 Chevrolet Silverado 3500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
Note: All existing transmitters will need to be reprogrammed during this procedure M
- Close all vehicle doors.
- Insert key into ignition
- Hold down the UNLOCK button on the driver side door panel. Continue to hold down until instructed to release in step 9.
- Perform steps 5 through 8 in fairly rapid succession.
- Turn the ignition switch to the ON position (do not crank the engine)
- Turn the ignition switch to the OFF position.
- Turn the ignition switch to the ON position ( do not crank the engine).
- Turn the ignition switch to the OFF position.
- Release the unlock button on the door panel. The vehicle should lock and unlock the doors automatically.
- Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the doors lock and unlock to confirm programming. – (You may need to hold LOCK & UNLOCK for up to 30 seconds.)
- Repeat step 10 for each additional transmitter (including any preexisting transmitters).
- Turn the ignition switch to the ON position to exit the transmitter programming mode.
2002 Chevrolet Silverado 3500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2003 Chevrolet Silverado 3500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2004 Chevrolet Silverado 3500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2005 Chevrolet Silverado 3500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
You must have all GM remotes including working ones when performing this procedure. (This procedure essentially wipes allremotes from the vehicles memory so all must be reprogrammed***Press each button on the remote 26 times (lock x 26, unlock x 26, horn x26) then attempt the steps outlined below***
- Close all doors on the vehicle.
- Then insert key into the ignition.
- Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in step 5.
- Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just before of starting your vehicle, OFF is the position whereyou can pull your key out of the ignition)
- Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. If locks cycle then continue to step 6.(if the door locks begin to lock and unlock BEFORE releasing the unlock buttonthen the vehicle has not entered programming mode and you must start over. Remove key, open door and return to step 1. If thevehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicles system and remotesmust be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key tooquick, too slow, there’s a problem with the vehicles system, or the vehicle is not equipped with a factory keyless entry system.
- Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30seconds.
- NOW repeat step 6. for all additional remotes including working ones.
- After step 6. has been performed for all remotes TURN ignition to ON to exit programming mode.
- Turn ignition OFF, remove key and test all remotes to make sure that they are all properly programmed.
2006 Chevrolet Silverado 3500 HD Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2007 Chevrolet Silverado 3500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2008 Chevrolet Silverado 3500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2009 Chevrolet Silverado 3500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2010 Chevrolet Silverado 3500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2011 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Chevrolet Silverado 3500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2012 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Chevrolet Silverado 3500 HD Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2013 Chevrolet Silverado 3500 HD Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Chevrolet Sonic | 2012 | Programming Instructions |
Chevrolet Sonic | 2013 | Programming Instructions |
Chevrolet Sonic | 2014 | Programming Instructions |
Chevrolet Sonic | 2015 | Programming Instructions |
Chevrolet Sonic | 2016 | Programming Instructions |
Chevrolet Sonic | 2017 | Programming Instructions |
Chevrolet Sonic | 2018 | Programming Instructions |
Chevrolet Sonic | 2019 | Programming Instructions |
Chevrolet Sonic | 2020 | Programming Instructions |
2012 Chevrolet Sonic Keyless Entry Remote Fob Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2013 Chevrolet Sonic Keyless Entry Remote Fob Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2014 Chevrolet Sonic Keyless Entry Remote Fob Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2015 Chevrolet Sonic Keyless Entry Remote Fob Programming Instructions
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
This procedure requires that a programmed working key is available for the vehicle. This procedure adds keys only. The procedure does not erase previously learned keys. The new key to be programmed needs to be cut prior to performing this programming procedure.
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):
1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:
A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be-off and all of the transmitters, both currently recognized and new, must be with you. The key blade needs to be cut prior to performing this programming procedure.
- Place the recognized (already programmed) transmitter in the cupholder.
- Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
- Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
- Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
- Remove the transmitter from the transmitter pocket and press the unlock button.
To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.
2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:
lf there are no currently recognized transmitters available, follow this procedure to program up to five transmitters. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all of the transmitters you wish to program must be with you. The key blade needs to be cut prior to performing this programming procedure. It is recommended that the vehicle be connected to a power source via jumper cables during this procedure as the vehicle’s battery voltage will drop during the procedure.
- Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
- Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
- Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
- Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
- Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
- Remove the transmitter from the transmitter pocket and press the unlock button.
To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.
Please note: Each vehicle can have up to five transmitters programmed to it.
2016 Chevrolet Sonic Keyless Entry Remote Fob Programming Instructions
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
This procedure requires that a programmed working key is available for the vehicle. This procedure adds keys only. The procedure does not erase previously learned keys. The new key to be programmed needs to be cut prior to performing this programming procedure.
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):
1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:
A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be-off and all of the transmitters, both currently recognized and new, must be with you. The key blade needs to be cut prior to performing this programming procedure.
- Place the recognized (already programmed) transmitter in the cupholder.
- Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
- Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
- Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
- Remove the transmitter from the transmitter pocket and press the unlock button.
To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.
2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:
lf there are no currently recognized transmitters available, follow this procedure to program up to five transmitters. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all of the transmitters you wish to program must be with you. The key blade needs to be cut prior to performing this programming procedure. It is recommended that the vehicle be connected to a power source via jumper cables during this procedure as the vehicle’s battery voltage will drop during the procedure.
- Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
- Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
- Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
- Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
- Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
- Remove the transmitter from the transmitter pocket and press the unlock button.
To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.
Please note: Each vehicle can have up to five transmitters programmed to it.
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2017 Chevrolet Sonic Keyless Entry Remote Fob Programming Instructions
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
This procedure requires that a programmed working key is available for the vehicle. This procedure adds keys only. The procedure does not erase previously learned keys. The new key to be programmed needs to be cut prior to performing this programming procedure.
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):
1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:
A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be-off and all of the transmitters, both currently recognized and new, must be with you. The key blade needs to be cut prior to performing this programming procedure.
- Place the recognized (already programmed) transmitter in the cupholder.
- Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
- Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
- Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
- Remove the transmitter from the transmitter pocket and press the unlock button.
To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.
2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:
lf there are no currently recognized transmitters available, follow this procedure to program up to five transmitters. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all of the transmitters you wish to program must be with you. The key blade needs to be cut prior to performing this programming procedure. It is recommended that the vehicle be connected to a power source via jumper cables during this procedure as the vehicle’s battery voltage will drop during the procedure.
- Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
- Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
- Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
- Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
- Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
- Remove the transmitter from the transmitter pocket and press the unlock button.
To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.
Please note: Each vehicle can have up to five transmitters programmed to it.
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2018 Chevrolet Sonic Keyless Entry Remote Fob Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2019 Chevrolet Sonic Keyless Entry Remote Fob Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2020 Chevrolet Sonic Keyless Entry Remote Fob Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
Model | Year | |
---|---|---|
Chevrolet Spark | 2016 | Programming Instructions |
Chevrolet Spark | 2017 | Programming Instructions |
Chevrolet Spark | 2018 | Programming Instructions |
Chevrolet Spark | 2019 | Programming Instructions |
Chevrolet Spark | 2020 | Programming Instructions |
2016 Chevrolet Spark Keyless Entry Remote Fob Programming Instructions
If you have a remote flip key, the remote portion is programmed during the Key Programming procedure.
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2016 Chevrolet Spark Key Programming Instructions
These instructions work only for non-PEPS keys. They will not work if your vehicle has passive entry.
Also, these programming instructions will not work if you have Canadian vehicle.
This procedure adds keys only. Previously programmed keys will not be erased.
This procedure will program both remote and key portions.
Your new unprogrammed key must be cut before performing these steps:
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2017 Chevrolet Spark Keyless Entry Remote Fob Programming Instructions
If you have a remote flip key, the remote portion is programmed during the Key Programming procedure.
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2016 Chevrolet Spark Key Programming Instructions
These instructions work only for non-PEPS keys. They will not work if your vehicle has passive entry.
Also, these programming instructions will not work if you have Canadian vehicle.
This procedure adds keys only. Previously programmed keys will not be erased.
This procedure will program both remote and key portions.
Your new unprogrammed key must be cut before performing these steps:
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2018 Chevrolet Spark Keyless Entry Remote Fob Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2019 Chevrolet Spark Keyless Entry Remote Fob Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
2020 Chevrolet Spark Keyless Entry Remote Fob Programming Instructions
DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):
A. Programming with Two Working Smart Keys
Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
- Remove the emergency key blade from one of the working smart keys.
- Place the two working smart keys in the cupholder.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
- To program an additional smart key, repeat Steps 4-6.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
B. Programming without Two Working Smart Keys
If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.
Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.
- Remove the key blade from your existing or new smart key.
- Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
- Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
- Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
- Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
- Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
- Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
- To program an additional smart key, repeat Steps 6-8.
When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.
Model | Year | |
---|---|---|
Chevrolet SSR | 2003 | Programming Instructions |
Chevrolet SSR | 2004 | Programming Instructions |
Chevrolet SSR | 2005 | Programming Instructions |
Chevrolet SSR | 2006 | Programming Instructions |
2003 Chevrolet SSR Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Chevrolet SSR Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Chevrolet SSR Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Chevrolet SSR Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.