Ford Keyless Entry Remote Fob Programming Instructions Page 4
Keyless Entry Remote Fob Programming Instructions Available for the following Ford models.
Click below to select your model.
| Model | Year | |
|---|---|---|
| Ford Transit | 2013 | Programming Instructions |
2013 Ford Transit Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
2013 Ford Transit Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
| Model | Year | |
|---|---|---|
| Ford Transit Connect | 2010 | Programming Instructions |
| Ford Transit Connect | 2011 | Programming Instructions |
| Ford Transit Connect | 2012 | Programming Instructions |
| Ford Transit Connect | 2013 | Programming Instructions |
| Ford Transit Connect | 2014 | Programming Instructions |
| Ford Transit Connect | 2015 | Programming Instructions |
2010 Ford Transit Connect Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
2010 Ford Transit Connect Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2011 Ford Transit Connect Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
2011 Ford Transit Connect Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2012 Ford Transit Connect Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
2012 Ford Transit Connect Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2013 Ford Transit Connect Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
2013 Ford Transit Connect Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2014 Ford Transit Connect Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
2014 Ford Transit Connect Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2015 Ford Transit Connect Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
2015 Ford Transit Connect Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
| Model | Year | |
|---|---|---|
| Ford Windstar | 1998 | Programming Instructions |
| Ford Windstar | 1999 | Programming Instructions |
| Ford Windstar | 2000 | Programming Instructions |
| Ford Windstar | 2001 | Programming Instructions |
| Ford Windstar | 2002 | Programming Instructions |
| Ford Windstar | 2003 | Programming Instructions |
1998 Ford Windstar Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
1998 Ford Windstar Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you..
Find A Locksmith
1999 Ford Windstar Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
1999 Ford Windstar Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2000 Ford Windstar Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
2000 Ford Windstar Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2001 Ford Windstar Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
2001 Ford Windstar Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2002 Ford Windstar Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
2002 Ford Windstar Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
2003 Ford Windstar Keyless Entry Remote Fob Programming Instructions
FORD REMOTE – THIS PROCEDURE RESETS ALL REMOTES FOR THE VEHICLE. ALL FUNCTIONING REMOTES WILL HAVE TO BE REPROGRAMMED DURING THE PROCEDURE
There are a few different procedures that will program your remotes depending on what vehicle that you have. You can find your exact procedure in your owners manual. If you do not have your owners manual you can try any of the procedures below until you find the one that works for your vehicles
Make sure that you don’t press the brake pedal at any time during or before the procedure.
Procedure A:
- Close all doors, then open drivers door and press the Unlock button on driver’s door while it is open, insert key into ignition.
- Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (if the door locks do not cycle, then it was done incorrectly. You must start over by removing key and beginning from step 1) (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 10 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 5.
- Within 10 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 4. for all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
*If this does not work try the procedure with the door closed.
Procedure B:
- Fasten seatbelt and close all doors
- Turn the ignition from OFF to RUN 4 times within 3 seconds.
- Turn the ignition OFF. The system will chime to confirm programming mode.
- Within 10 seconds, press and hold any button on first keyless remote. The system will chime once to confirm programming.
- Within 10 seconds, press and hold any button on second keyless remote. System will chime once to confirm programming.
- Turn ignition to RUN to exit programming mode.
Please note: All steps should be performed in fairly rapid succession. If you never get the initial chime or door lock cycle, that means the vehicle has never entered programming mode. You should remove key from ignition, open and close the door and start over.
2003 Ford Windstar Key Programming Instructions
You must have 2 original keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.
Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
- Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
- The security light will light up for THREE seconds to indicate the new key has been successfully programmed.
For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.
