Infiniti Keyless Entry Remote Fob Programming Instructions
Keyless Entry Remote Fob Programming Instructions Available for the following Infiniti models.
Click below to select your model.
Model | Year | |
---|---|---|
Infiniti EX35 | 2008 | Programming Instructions |
Infiniti EX35 | 2009 | Programming Instructions |
Infiniti EX35 | 2010 | Programming Instructions |
Infiniti EX35 | 2011 | Programming Instructions |
Infiniti EX35 | 2012 | Programming Instructions |
2008 Infiniti EX35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2008 Infiniti EX35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Infiniti EX35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2009 Infiniti EX35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Infiniti EX35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2010 Infiniti EX35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Infiniti EX35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2011 Infiniti EX35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Infiniti EX35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti EX37 | 2013 | Programming Instructions |
2013 Infiniti EX37 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti FX35 | 2008 | Programming Instructions |
Infiniti FX35 | 2009 | Programming Instructions |
Infiniti FX35 | 2010 | Programming Instructions |
Infiniti FX35 | 2011 | Programming Instructions |
Infiniti FX35 | 2012 | Programming Instructions |
2008 Infiniti FX35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2008 Infiniti FX35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Infiniti FX35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2009 Infiniti FX35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Infiniti FX35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Infiniti FX35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Infiniti FX35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti FX37 | 2013 | Programming Instructions |
2013 Infiniti FX37 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti FX45 | 2003 | Programming Instructions |
Infiniti FX45 | 2004 | Programming Instructions |
Infiniti FX45 | 2005 | Programming Instructions |
Infiniti FX45 | 2006 | Programming Instructions |
Infiniti FX45 | 2007 | Programming Instructions |
Infiniti FX45 | 2008 | Programming Instructions |
2003 Infiniti FX45 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2003 Infiniti FX45 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Infiniti FX45 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2004 Infiniti FX45 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Infiniti FX45 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2005 Infiniti FX45 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Infiniti FX45 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2006 Infiniti FX45 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Infiniti FX45 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2007 Infiniti FX45 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Infiniti FX45 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2008 Infiniti FX45 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti FX50 | 2009 | Programming Instructions |
Infiniti FX50 | 2010 | Programming Instructions |
Infiniti FX50 | 2011 | Programming Instructions |
Infiniti FX50 | 2012 | Programming Instructions |
Infiniti FX50 | 2013 | Programming Instructions |
2009 Infiniti FX50 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Infiniti FX50 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Infiniti FX50 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Infiniti FX50 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2013 Infiniti FX50 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti G20 | 2000 | Programming Instructions |
Infiniti G20 | 2001 | Programming Instructions |
Infiniti G20 | 2002 | Programming Instructions |
2000 Infiniti G20 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Infiniti G20 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Infiniti G20 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti G35 | 2003 | Programming Instructions |
Infiniti G35 | 2004 | Programming Instructions |
Infiniti G35 | 2005 | Programming Instructions |
Infiniti G35 | 2006 | Programming Instructions |
Infiniti G35 | 2007 | Programming Instructions |
Infiniti G35 | 2008 | Programming Instructions |
2003 Infiniti G35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2003 Infiniti G35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Infiniti G35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2004 Infiniti G35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Infiniti G35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2005 Infiniti G35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Infiniti G35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2006 Infiniti G35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Infiniti G35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Infiniti G35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti G37 | 2008 | Programming Instructions |
Infiniti G37 | 2009 | Programming Instructions |
Infiniti G37 | 2010 | Programming Instructions |
2008 Infiniti G37 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Infiniti G37 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Infiniti G37 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti I30 | 2000 | Programming Instructions |
Infiniti I30 | 2001 | Programming Instructions |
Infiniti I30 | 2002 | Programming Instructions |
Infiniti I30 | 2003 | Programming Instructions |
Infiniti I30 | 2004 | Programming Instructions |
2000 Infiniti I30 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Infiniti I30 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Infiniti I30 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Infiniti I30 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Infiniti I30 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti I35 | 2000 | Programming Instructions |
Infiniti I35 | 2001 | Programming Instructions |
Infiniti I35 | 2002 | Programming Instructions |
Infiniti I35 | 2003 | Programming Instructions |
Infiniti I35 | 2004 | Programming Instructions |
2000 Infiniti I35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Infiniti I35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Infiniti I35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2002 Infiniti I35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Infiniti I35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2003 Infiniti I35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Infiniti I35 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2004 Infiniti I35 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti JX35 | 2013 | Programming Instructions |
Infiniti JX35 | 2014 | Programming Instructions |
2013 Infiniti JX35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2014 Infiniti JX35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti M35 | 2006 | Programming Instructions |
Infiniti M35 | 2007 | Programming Instructions |
Infiniti M35 | 2008 | Programming Instructions |
Infiniti M35 | 2009 | Programming Instructions |
Infiniti M35 | 2010 | Programming Instructions |
2006 Infiniti M35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Infiniti M35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Infiniti M35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Infiniti M35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Infiniti M35 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti M45 | 2006 | Programming Instructions |
Infiniti M45 | 2007 | Programming Instructions |
Infiniti M45 | 2008 | Programming Instructions |
Infiniti M45 | 2009 | Programming Instructions |
Infiniti M45 | 2010 | Programming Instructions |
2006 Infiniti M45 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Infiniti M45 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Infiniti M45 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Infiniti M45 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Infiniti M45 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti Q40 | 2015 | Programming Instructions |
2015 Infiniti Q40 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti Q45 | 2003 | Programming Instructions |
Infiniti Q45 | 2004 | Programming Instructions |
Infiniti Q45 | 2005 | Programming Instructions |
Infiniti Q45 | 2006 | Programming Instructions |
2003 Infiniti Q45 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2003 Infiniti Q45 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Infiniti Q45 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Infiniti Q45 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2005 Infiniti Q45 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Infiniti Q45 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2006 Infiniti Q45 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti QX4 | 1999 | Programming Instructions |
Infiniti QX4 | 2000 | Programming Instructions |
Infiniti QX4 | 2001 | Programming Instructions |
Infiniti QX4 | 2002 | Programming Instructions |
Infiniti QX4 | 2003 | Programming Instructions |
Infiniti QX4 | 2004 | Programming Instructions |
1999 Infiniti QX4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Infiniti QX4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Infiniti QX4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Infiniti QX4 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2002 Infiniti QX4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Infiniti QX4 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2003 Infiniti QX4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Infiniti QX4 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2004 Infiniti QX4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti QX56 | 2004 | Programming Instructions |
Infiniti QX56 | 2005 | Programming Instructions |
Infiniti QX56 | 2006 | Programming Instructions |
Infiniti QX56 | 2007 | Programming Instructions |
Infiniti QX56 | 2010 | Programming Instructions |
Infiniti QX56 | 2011 | Programming Instructions |
Infiniti QX56 | 2012 | Programming Instructions |
Infiniti QX56 | 2013 | Programming Instructions |
2004 Infiniti QX56 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2004 Infiniti QX56 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Infiniti QX56 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2005 Infiniti QX56 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Infiniti QX56 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2006 Infiniti QX56 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Infiniti QX56 Keyless Entry Remote Fob Programming Instructions
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
- Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
- Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
- Insert key into ignition and turn to the ACC position.
- Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
- If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
- When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.
2007 Infiniti QX56 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Infiniti QX56 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Infiniti QX56 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Infiniti QX56 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2013 Infiniti QX56 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti QX60 | 2014 | Programming Instructions |
Infiniti QX60 | 2019 | Programming Instructions |
Infiniti QX60 | 2020 | Programming Instructions |
2014 Infiniti QX60 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2019 Infiniti QX60 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2020 Infiniti QX60 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
Model | Year | |
---|---|---|
Infiniti QX70 | 2014 | Programming Instructions |
Infiniti QX70 | 2015 | Programming Instructions |
2014 Infiniti QX70 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2015 Infiniti QX70 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.