Lexus Keyless Entry Remote Fob Programming Instructions

1998 Lexus ES300 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

1998 Lexus ES300 Key Programming Instructions

Add Duplicate Key

1. Insert an existing master key into the ignition cylinder.
Do not turn the key from the OFF (LOCK) position.
2. Within fifteen seconds of inserting the key, depress and release the accelerator pedal 4 times.
3. Within 20 seconds of completing the above step, depress and release the brake pedal 5 times and then remove the original key from the ignition.
4. Within 10 second, insert the new key into the ignition. Do not turn the key from the OFF (LOCK) position.
5. Within 10 seconds depress and release the accelerator pedal 1 time.
6. After 80 seconds the new key has been learned by the vehicle’s on-board computer and the Security light will go off.

Remove the new key and depress and release the brake pedal 1 time.

To delete all but one key from the unit:

1. Insert an existing master key into the ignition cylinder. Do not turn the key from the OFF (LOCK) position.
2. Within fifteen seconds of inserting the key, depress and release the accelerator pedal six times.
3. Within twenty seconds of completing the above step, depress and release the brake pedal seven times.
4. The security light will flash, indicating all keys other than the one being used have been deleted.
5. Remove the key from the ignition cylinder within ten seconds. It will be the only key still programmed to work.

1999 Lexus ES300 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

1999 Lexus ES300 Key Programming Instructions

Add Duplicate Key

1. Insert an existing master key into the ignition cylinder.
Do not turn the key from the OFF (LOCK) position.
2. Within fifteen seconds of inserting the key, depress and release the accelerator pedal 4 times.
3. Within 20 seconds of completing the above step, depress and release the brake pedal 5 times and then remove the original key from the ignition.
4. Within 10 second, insert the new key into the ignition. Do not turn the key from the OFF (LOCK) position.
5. Within 10 seconds depress and release the accelerator pedal 1 time.
6. After 80 seconds the new key has been learned by the vehicle’s on-board computer and the Security light will go off.

Remove the new key and depress and release the brake pedal 1 time.

To delete all but one key from the unit:

1. Insert an existing master key into the ignition cylinder. Do not turn the key from the OFF (LOCK) position.
2. Within fifteen seconds of inserting the key, depress and release the accelerator pedal six times.
3. Within twenty seconds of completing the above step, depress and release the brake pedal seven times.
4. The security light will flash, indicating all keys other than the one being used have been deleted.
5. Remove the key from the ignition cylinder within ten seconds. It will be the only key still programmed to work.

2000 Lexus ES300 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2000 Lexus ES300 Key Programming Instructions

Add Duplicate Key

1. Insert an existing master key into the ignition cylinder.
Do not turn the key from the OFF (LOCK) position.
2. Within fifteen seconds of inserting the key, depress and release the accelerator pedal 4 times.
3. Within 20 seconds of completing the above step, depress and release the brake pedal 5 times and then remove the original key from the ignition.
4. Within 10 second, insert the new key into the ignition. Do not turn the key from the OFF (LOCK) position.
5. Within 10 seconds depress and release the accelerator pedal 1 time.
6. After 80 seconds the new key has been learned by the vehicle’s on-board computer and the Security light will go off.

Remove the new key and depress and release the brake pedal 1 time.

To delete all but one key from the unit:

1. Insert an existing master key into the ignition cylinder. Do not turn the key from the OFF (LOCK) position.
2. Within fifteen seconds of inserting the key, depress and release the accelerator pedal six times.
3. Within twenty seconds of completing the above step, depress and release the brake pedal seven times.
4. The security light will flash, indicating all keys other than the one being used have been deleted.
5. Remove the key from the ignition cylinder within ten seconds. It will be the only key still programmed to work.

2001 Lexus ES300 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2001 Lexus ES300 Key Programming Instructions

Add Duplicate Key

1. Insert an existing master key into the ignition cylinder.
Do not turn the key from the OFF (LOCK) position.
2. Within fifteen seconds of inserting the key, depress and release the accelerator pedal 4 times.
3. Within 20 seconds of completing the above step, depress and release the brake pedal 5 times and then remove the original key from the ignition.
4. Within 10 second, insert the new key into the ignition. Do not turn the key from the OFF (LOCK) position.
5. Within 10 seconds depress and release the accelerator pedal 1 time.
6. After 80 seconds the new key has been learned by the vehicle’s on-board computer and the Security light will go off.

Remove the new key and depress and release the brake pedal 1 time.

To delete all but one key from the unit:

1. Insert an existing master key into the ignition cylinder. Do not turn the key from the OFF (LOCK) position.
2. Within fifteen seconds of inserting the key, depress and release the accelerator pedal six times.
3. Within twenty seconds of completing the above step, depress and release the brake pedal seven times.
4. The security light will flash, indicating all keys other than the one being used have been deleted.
5. Remove the key from the ignition cylinder within ten seconds. It will be the only key still programmed to work.

2002 Lexus ES300 Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
Insert the key into the ignition (Do NOT Turn it) and Pull key out.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)

Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2002 Lexus ES300 Key Programming Instructions

Have your master Toyota key at hand (black key)

1. Insert black programmed key into ignition.
2. Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
3. Press and release brake pedal 6 times within 20 seconds of step 2.
4. Remove black key from ignition switch.
5. Insert new unprogrammed key into ignition within 10 seconds of step 4.
6. Press and release accelerator pedal once within 10 seconds of step 5.
7. Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one
minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
8. Within ten seconds of inserting key into ignition press and release accelerator pedal once.
9. Immobilizer warning lamp will flash and after one minute the lamp will shut off.

2003 Lexus ES300 Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
Insert the key into the ignition (Do NOT Turn it) and Pull key out.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)

Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2003 Lexus ES300 Key Programming Instructions

Have your master Toyota key at hand (black key)

1. Insert black programmed key into ignition.
2. Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
3. Press and release brake pedal 6 times within 20 seconds of step 2.
4. Remove black key from ignition switch.
5. Insert new unprogrammed key into ignition within 10 seconds of step 4.
6. Press and release accelerator pedal once within 10 seconds of step 5.
7. Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one
minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
8. Within ten seconds of inserting key into ignition press and release accelerator pedal once.
9. Immobilizer warning lamp will flash and after one minute the lamp will shut off.

2004 Lexus ES300 Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
Insert the key into the ignition (Do NOT Turn it) and Pull key out.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)

Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2004 Lexus ES300 Key Programming Instructions

Have your master Toyota key at hand (black key)

1. Insert black programmed key into ignition.
2. Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
3. Press and release brake pedal 6 times within 20 seconds of step 2.
4. Remove black key from ignition switch.
5. Insert new unprogrammed key into ignition within 10 seconds of step 4.
6. Press and release accelerator pedal once within 10 seconds of step 5.
7. Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one
minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
8. Within ten seconds of inserting key into ignition press and release accelerator pedal once.
9. Immobilizer warning lamp will flash and after one minute the lamp will shut off.

2005 Lexus ES300 Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
Insert the key into the ignition (Do NOT Turn it) and Pull key out.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)

Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2005 Lexus ES300 Key Programming Instructions

Have your master Toyota key at hand (black key)

1. Insert black programmed key into ignition.
2. Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
3. Press and release brake pedal 6 times within 20 seconds of step 2.
4. Remove black key from ignition switch.
5. Insert new unprogrammed key into ignition within 10 seconds of step 4.
6. Press and release accelerator pedal once within 10 seconds of step 5.
7. Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one
minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
8. Within ten seconds of inserting key into ignition press and release accelerator pedal once.
9. Immobilizer warning lamp will flash and after one minute the lamp will shut off.

2006 Lexus ES300 Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
Insert the key into the ignition (Do NOT Turn it) and Pull key out.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)

Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2006 Lexus ES300 Key Programming Instructions

Have your master Toyota key at hand (black key)

1. Insert black programmed key into ignition.
2. Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
3. Press and release brake pedal 6 times within 20 seconds of step 2.
4. Remove black key from ignition switch.
5. Insert new unprogrammed key into ignition within 10 seconds of step 4.
6. Press and release accelerator pedal once within 10 seconds of step 5.
7. Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one
minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
8. Within ten seconds of inserting key into ignition press and release accelerator pedal once.
9. Immobilizer warning lamp will flash and after one minute the lamp will shut off.

2004 Lexus ES330 Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
Insert the key into the ignition (Do NOT Turn it) and Pull key out.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)

Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2004 Lexus ES330 Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you..

2005 Lexus ES330 Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
Insert the key into the ignition (Do NOT Turn it) and Pull key out.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)

Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2005 Lexus ES330 Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you..

2006 Lexus ES330 Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
Insert the key into the ignition (Do NOT Turn it) and Pull key out.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)

Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2006 Lexus ES330 Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you..

2007 Lexus ES330 Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
Insert the key into the ignition (Do NOT Turn it) and Pull key out.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)

Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2007 Lexus ES330 Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you..