Saturn Keyless Entry Remote Fob Programming Instructions
Keyless Entry Remote Fob Programming Instructions Available for the following Saturn models.
Click below to select your model.
| Model | Year | |
|---|---|---|
| Saturn Aura | 2007 | Programming Instructions |
| Saturn Aura | 2008 | Programming Instructions |
| Saturn Aura | 2009 | Programming Instructions |
| Saturn Aura | 2010 | Programming Instructions |
2007 Saturn Aura Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.Dear automotive professional, If the vehicle does not accept the remote during your standard programming procedure, please try these steps. Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes. Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2007 Saturn Aura Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Saturn Aura Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.Dear automotive professional, If the vehicle does not accept the remote during your standard programming procedure, please try these steps. Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes. Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2008 Saturn Aura Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Saturn Aura Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.Dear automotive professional, If the vehicle does not accept the remote during your standard programming procedure, please try these steps. Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes. Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2009 Saturn Aura Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Saturn Aura Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Saturn Aura Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
| Model | Year | |
|---|---|---|
| Saturn Outlook | 2007 | Programming Instructions |
| Saturn Outlook | 2008 | Programming Instructions |
| Saturn Outlook | 2009 | Programming Instructions |
| Saturn Outlook | 2010 | Programming Instructions |
2007 Saturn Outlook Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2007 Saturn Outlook Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Saturn Outlook Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2008 Saturn Outlook Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Saturn Outlook Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2009 Saturn Outlook Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Saturn Outlook Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Saturn Outlook Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
| Model | Year | |
|---|---|---|
| Saturn Relay-1 | 2007 | Programming Instructions |
2007 Saturn Relay-1 Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.Dear automotive professional, If the vehicle does not accept the remote during your standard programming procedure, please try these steps. Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes. Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2007 Saturn Relay-1 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Saturn Relay-2 | 2005 | Programming Instructions |
| Saturn Relay-2 | 2006 | Programming Instructions |
| Saturn Relay-2 | 2007 | Programming Instructions |
2005 Saturn Relay-2 Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.Dear automotive professional, If the vehicle does not accept the remote during your standard programming procedure, please try these steps. Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes. Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2005 Saturn Relay-2 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Saturn Relay-2 Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.Dear automotive professional, If the vehicle does not accept the remote during your standard programming procedure, please try these steps. Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes. Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2006 Saturn Relay-2 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Saturn Relay-2 Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.Dear automotive professional, If the vehicle does not accept the remote during your standard programming procedure, please try these steps. Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes. Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2007 Saturn Relay-2 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Saturn Relay-3 | 2005 | Programming Instructions |
| Saturn Relay-3 | 2006 | Programming Instructions |
| Saturn Relay-3 | 2007 | Programming Instructions |
2005 Saturn Relay-3 Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.Dear automotive professional, If the vehicle does not accept the remote during your standard programming procedure, please try these steps. Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes. Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2005 Saturn Relay-3 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Saturn Relay-3 Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.Dear automotive professional, If the vehicle does not accept the remote during your standard programming procedure, please try these steps. Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes. Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2006 Saturn Relay-3 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Saturn Relay-3 Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.Dear automotive professional, If the vehicle does not accept the remote during your standard programming procedure, please try these steps. Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes. Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2007 Saturn Relay-3 Key Programming
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Saturn Sky | 2007 | Programming Instructions |
| Saturn Sky | 2008 | Programming Instructions |
| Saturn Sky | 2009 | Programming Instructions |
| Saturn Sky | 2010 | Programming Instructions |
2007 Saturn Sky Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Saturn Sky Key Programming
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Saturn Sky Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Saturn Sky Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Saturn Sky Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Saturn Sky Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Saturn Sky Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Saturn Sky Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
| Model | Year | |
|---|---|---|
| Saturn SL1 | 1999 | Programming Instructions |
1999 Saturn SL1 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Saturn Vue | 2004 | Programming Instructions |
| Saturn Vue | 2005 | Programming Instructions |
| Saturn Vue | 2006 | Programming Instructions |
| Saturn Vue | 2007 | Programming Instructions |
| Saturn Vue | 2008 | Programming Instructions |
| Saturn Vue | 2009 | Programming Instructions |
2004 Saturn Vue Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Saturn Vue Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Saturn Vue Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Saturn Vue Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Saturn Vue Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Saturn Vue Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Saturn Vue Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Saturn Vue Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
